LAM 810-048219-021 PXI模拟输入卡

产品概述：

810-048219-021离散输入输入类型：接地参考的离散输入输入阈值：<2 V（dc）=“ON”>7 V（dc 负载）负载范围：48 至100k 保护：短路保护将在激活时切断输出电源，并需要电源循环才能清除CAN通信类型：2线CAN，版本2.0B，带29位标识符协议：符合SAE J1939，810-048219-021但使用专有组扩展可配置数据速率：810-048219-021250 kbps、500 kbps和1 Mbps CAN端接：跳线可选端接电阻器（125) 总线长度：数据速率（bps）最大长度米（英尺）250 k 250（820）500 k 100（328）1 M 40（131）故障检测：服务模式软件设置RS-232串行通信服务端口隔离：无波特率：固定19.2 Kbaud机械接口：9针sub-D公连接器引脚输出：Tx=引脚2，Rx=引脚3，Gnd=引脚5最大电缆长度：15 m（50 ft，最大I/O延迟：1

 至少100毫米（4英寸）的紧密包装、810-048219-021行业认可的包装材料； 双壁包装纸箱； 在纸箱外面缠上一条结实的带子以增强强度。为防止不当操作对电子元件造成损坏，请阅读并遵守810-048219-021手册82715《电子控制、印刷电路板和模块的操作和保护指南》中的注意事项。更换零件在订购控制装置的更换零件时，包括以下信息：810-048219-021 外壳铭牌上的零件号（XXXX-XXXX）； 机组序列号，也在铭牌上。

 description of the problem; ·810-048219-021 instructions describing the desired type of repair. Packing a Control Use the following materials when returning a complete control: · protective caps on any connectors; · antistatic protective bags on all electronic modules; · 810-048219-021packing materials that will not damage the surface of the unit; · at least 100 mm (4 inches) of tightly packed, industry-approved packing material; · a packing carton with double walls; ·810-048219-021 a strong tape around the outside of the carton for increased strength. 

 description of the problem; · instructions describing the desired type of repair. Packing a Control Use the following materials when returning a complete control: ·810-048219-021 protective caps on any connectors; · antistatic protective bags on all electronic modules; ·810-048219-021 packing materials that will not damage the surface of the unit; · at least 100 mm (4 inches) of tightly packed, industry-approved packing material; ·810-048219-021 a packing carton with double walls; · 810-048219-021a strong tape around the outside of the carton for increased strength. 

Flat Rate Remanufacture is very similar to the Flat Rate Repair option, with the exception that the unit will be returned to you in “likenew” condition.810-048219-021 This option is applicable to mechanical products only. Returning Equipment for Repair If a control (or any part of an electronic control) is to be returned for repair, please contact your Full-Service Distributor in advance to obtain Return Authorization and shipping instructions. When shipping the item(s), attach a tag with the following information: · return number; · name and location where the control is installed; ·810-048219-021 name and phone number of contact person; ·810-048219-021 complete Woodward part number(s) and serial number(s);