LAM 810-800031-400 PCB板
产品概述:
810-800031-400此命令可以在true和false之间切换。当切换到true时,机组将保持关闭状态,直到该参数设置回false或ProAct上的电源循环。状态-报警-报警条件存在的一般指示,具体报警条件请参阅状态错误-报警选项卡页。Status–Shutdown–存在Shutdown条件的一般指示,有关特定条件,请参阅Status Error–Shutdowns选项卡页。状态-低功率标准差-机组处于低功率待机模式的一般指示,810-800031-400有关具体情况,请参阅状态错误-停机选项卡页。服务:位置控制位置控制选项卡工作表包含位置控制信息。位置需求(%)——基于装置配置的实际位置需求信号的指示,单位为用户校准范围的百分比。实际位置(%)——实际传动轴输出位置的指示,单位为用户校准范围的百分比。810-800031-400实际位置(度)——相对于绝对轴位置的实际驱动轴输出位置的指示,单位为旋转度。对于型号I至IV,完全逆时针方向为0度,完全顺时针方向为75度。
Mode Int——模式字符串的整数指示(见上文)810-800031-400。ProAct软件版本--显示已安装软件的版本号。Config ID--显示可配置软件系统的标识。此参数的默认值为ProAct Digital Plus Configuration,但此字符串可以在CFG文件中编辑为相对于特定应用程序设置更有意义的名称,然后下载回ProAct控件。CAN ProAct Number(CAN ProAct编号)—表示CAN通信中使用的识别号。基于上电时CAN ID Hi和Lo离散输入的状态。电子温度(°C)——检测到的电子设备温度的指示,单位为摄氏度。RunTime–810-800031-400清除命令—清除累积运行时间的命令。RunTime–Hours--自上次发出Run Time Clear命令以来的累计运行时数。每当装置通电并按小时存储时,或启用低功率待机模式离散输入时,时间就会累积。RunTime–100mSec——累计运行时间,单位为100毫秒(一小时36 000)。810-800031-400通电或清除命令时重置为零。每当装置通电并按小时存储时,或启用低功率待机模式离散输入时,时间就会累积。停机命令——810-800031-400使用维修工具强制装置进入停机状态的命令。有助于进入需要关闭设备的模式,如配置或调整用户停止。
Status–Shutdown—810-800031-400General indication that a Shutdown condition exists, refer to the Status Error—Shutdowns tab sheet for the specific condition. Status–Low Pwr Stdby—General indication that the unit is in Low Power Standby Mode, refer to the Status Error—Shutdowns tab sheet for the specific condition. Service: Position Control The Position Control tab sheet contains position control information. Position Demand (%)—Indication of the actual position demand signal,810-800031-400 based on unit configuration, in percentage of the user calibrated range. Actual Posn (%)—Indication of the actual driver shaft output position, in percentage of the user calibrated range. Actual Posn (deg)—Indication of the actual driver shaft output position, in degrees rotation, relative to absolute shaft position.810-800031-400 For models I through IV, full counterclockwise is zero degrees and full clockwise is 75 degrees.
Time accumulates whenever the unit is powered up and is stored on an hourly basis or if the Low Power Standby Mode discrete input is enabled. 810-800031-400RunTime–100mSec—Accumulated runtime in units of 100 ms (36 000 in an hour). Resets to zero on a power-up or Clear command. Time accumulates whenever the unit is powered-up and is stored on an hourly basis or if the Low Power Standby 810-800031-400Mode discrete input is enabled. Shutdown Command—Command to force the unit into a shutdown condition using the Service Tool. Helpful for entering into modes that require the unit to be shut down, like Configure or Adjust User Stops. This command can be toggled between true and false. When toggled to true, the unit remains in a shutdown state until this parameter is set back to false or the power is 810-800031-400 cycled on the ProAct. Status–Alarm—General indication that an alarm condition exists, refer to the Status Error—Alarms tab sheet for the specific alarm condition.810-800031-400
Mode Int—Integer indication of the mode string (see above). ProAct Software Version—Displays the version number of the software installed. 810-800031-400Config ID—Displays the identification of the software system configurables. The default for this parameter is ProAct Digital Plus Configuration, however this string can be edited in the CFG file to a more meaningful name relative to the specific application setup and then downloaded back into the ProAct control. CAN ProAct Number—Indication of the identification number used in the CAN communication. Based on the status of the CAN ID Hi and Lo discrete inputs at power-up.810-800031-400 Elect Temp (°C)—Indication of the detected electronics temperature in degrees Celsius. RunTime–Clear Command—Command to clear the accumulated RunTime.810-800031-400 RunTime–Hours—Accumulated runtime hours since the last Run Time Clear command was issued.