LAM 810-800256-004 中央集线器

810-800256-004配置中的错误将不允许执行机构运行，并将导致配置错误停机。错误代码解释（与下面的错误信息相同）0配置中没有错误101主/备用信号选择相同102无效的主需求信号选择103无效的备用需求信号选择104执行器惯性设置值太大105无效的执行器类型选择106无效的PwmIn最大/最小占空比值107无效的Analog in最大/分钟值108 CAN扩展必须非零错误信息（仅状态指示）配置状态的字符串指示（另请参阅错误代码）。810-800256-004配置中的错误将不允许执行机构运行，并将导致配置错误停机（请参阅停机信息）。810-800256-004关闭命令dflt=false（false，true）RS-232命令，关闭执行器驱动器。请参阅停机。配置：机组设置机组设置类别设置关键的执行机构和控制器信息。810-800256-004。在维修模式下可获得其他执行机构参数（请参阅“硬件调整”）。

Password dflt=0配置模式的密码输入命令810-800256-004。要输入值，请突出显示或删除默认值（“0”），然后使用键盘输入数字密码。当按下回车键或选择输入右侧的等号时，接受输入。输入后，密码将返回零。如果接受并关闭装置，“启用”指示将为真。有关维修工具密码，请参阅附录。已启用（仅状态指示）配置模式已启用指示（真/假）。810-800256-004启用模式时，参数为true–这表示可以更改配置模式参数。810-800256-004如果为false，则只能查看参数，而不能进行调整。退出dflt=false（仅限瞬时真命令）退出命令。设置为true可退出配置模式。这将禁用在此模式下更改参数的功能。810-800256-004“退出”参数在退出完成后自动返回false。错误代码（仅状态指示）配置状态的整数指示（另请参阅错误信息）。

(status indication only) String Indication of the status of the configuration (see also Error Code).810-800256-004 An error in the configuration will not allow the actuator to operate and will result in a Configuration Error Shutdown (see information on shutdowns).810-800256-004 Shutdown Command dflt = false (false, true) RS-232 Command to shut the actuator driver down. Refer to shutdowns. Configure: Unit Setup The Unit Setup category sets critical actuator and controller information. Refer to Figure 9-2.810-800256-004 Additional actuator parameters are available in the Service Mode (see ‘Hardware Adjustments’).

This disables the ability to make changes to parameters in this mode. The ‘Exit’ parameter automatically returns to false when the exit is completed. Error Code (status indication only) Integer Indication of the status of the configuration (see also Error Info).810-800256-004 An error in the configuration will not allow the actuator to operate and will result in a Configuration Error Shutdown. Error Code Interpretation (same as Error Info below) 0 No errors in configuration 101 Primary / Backup signal selection same 102 Invalid primary demand signal selection 103 Invalid backup demand signal selection 104 Actuator Inertia setting value too large 105 Invalid Actuator type selection 106 Invalid PwmIn max/min duty values 107 Invalid AnalogIn max/min values 108 CAN Extensions must be non-zero Error Info 

810-800256-004 Password dflt =0 Password input command for the Configure mode. To enter a value, highlight or delete the default value (‘0’) and use the keypad to enter the numeric password. The input is accepted when the enter key is pressed or the equals sign to the right of the input is selected.810-800256-004 When entered, the password returns to zero. If accepted and the unit is shut down, the 810-800256-004‘Enabled’ indication will be true. Refer to the Appendix for Service Tool passwords. Enabled (status indication only) Configure Mode Enabled Indication (true/false). Parameter is true when the mode is enabled – this indicates Configure mode parameters can be changed. When false, parameters can only be viewed – not adjusted. Exit dflt = false (momentary true command only) Exit command. Set to true to exit the Configure mode.810-800256-004