LAM 810-802901-305 开关量

如果装置的配置出现错误，810-802901-305（配置错误）关闭将使驱动器处于关闭状态。配置错误的确切原因在配置模式选项卡页上确定（请参阅配置错误部分）。配置错误配置完成后，将执行有效性检查。如果检测到错误，将发出Config error（配置错误）停机，并且在清除之前，机组不会运行。配置错误的原因可以从配置模式选项卡页上的错误代码和错误信息值中确定。错误代码错误信息（显示文本）0配置中没有错误810-802901-305主/备用信号选择相同（主需求和备用需求配置为同一源）102主需求信号选择无效（主需求选择配置为超出范围的值）810-802901-305备用需求信号选择无效（备用需求选择配置为超出范围值）104执行机构惯性设置值过大（执行机构惯性设定选择配置为超过范围值）810-802901-305无效执行机构类型选择（执行机构类型配置为超出范围值）

进入配置模式选择配置模式选项卡页，通过将关闭命令值设置为“true”或打开低功率待机模式离散输入来关闭驱动程序。输入适当的配置模式密码（1113），810-802901-305然后选择“输入”或单击密码框右侧的等于（=）框。如果已成功进入配置模式，“启用”字段将显示“true”。通过将装置设置和需求设置参数设置为特定于应用程序的值来配置装置。有关这些设置的详细信息，请参阅手册的配置模式详细信息部分。当对配置和服务模式参数进行更改时，它们会自动保存到非易失性存储器中——不需要特殊的“保存”命令。配置机组（配置模式参数）有关配置模式参数的详细信息，请参阅本章后面提供的信息。附录中提供了程序摘要工作表，作为ProAct控件中所有软件设置的概述。退出配置模式选择配置模式选项卡页，并将EXIT值设置为“true”。通过将停机命令值设置回“false”810-802901-305或关闭低功率待机模式离散输入，使机组返回运行（操作）状态。如果成功，维修模式/机组状态将显示“正在运行”（810-802901-305）。

 810-802901-305If an error is detected, the Config Error shutdown is issued and the unit will not run until it is cleared. The cause of the Configuration Error can be determined from the Error Code and Error Info values on the Configure Mode tab sheet.810-802901-305 Error Code Error Info (displayed text) 0 No errors in configuration 101 Primary / Backup signal selection same (the primary demand and backup demands are configured for the same source) 102 Invalid primary demand signal selection (the primary demand selection is configured for an out of range value) 103 Invalid backup demand signal selection (the backup demand selection is configured for an out of range value) 104 Actuator Inertia setting value too large (the actuator inertia setting selection is configured for an out of range value) 105 Invalid Actuator type selection 810-802901-305(the actuator type is configured for an out of range value)

Configuring the Unit810-802901-305 (Configure Mode parameters) Refer to the information provided later in this chapter for details on the Configure Mode parameters. A program summary worksheet is provided in the Appendix as an overview of all software settings in the ProAct control. Exiting Configure Mode Select the Configure Mode tab sheet and set the EXIT value to ‘true’. Return the unit to a running (operational) state by setting the Shutdown Command value back to ‘false’ or by closing the Low Power Standby Mode discrete input. The Service Mode / Unit Status will display ‘running’ if successful (refer to the Service Mode Details section). If an error was made in the unit’s configuration, a 810-802901-305 Config Error shutdown will hold the driver in a shutdown state. The exact cause of the Configuration Error is identified on the Configure Mode tab sheet (see Configuration Error section). Configuration Error Upon completion of the configuration 810-802901-305, a validity check is performed. 

Entering Configure Mode Select the Configure Mode tab sheet and shut down the driver by setting the Shutdown Command value to ‘true’ or 810-802901-305  by opening the Low Power Standby Mode discrete input. Enter the appropriate configure mode Password (1113) and either select ‘ENTER’ or click on the equals (=) box to the right of the password box. The ‘Enabled’ field will display 810-802901-305‘true’ if the Configure Mode has been successfully entered. Configure the unit by setting the Unit Setup and Demand Setup parameters to the application specific values. Refer to the Configure Mode Details section of the manual for details on these settings. As changes are made to Configure and Service mode parameters, they are automatically saved into non-volatile memory—no special ‘save’ command is required.810-802901-305